New vs NOS
Moderators: zaphod_phil, CurtissRobin, colossal
- basicbill
- Occasional poster
- Posts: 162
- Joined: Tue 06/30/09 2:00 am
- Location: Arizona
New vs NOS
My past experience with tubes suggests NOS tubes sound rounder/smoother than the new stuff.I have some Saratov EL-84'S from sarg. right now, very warm and round.Do they JJ's sound more edgey??
my previous exp. is mostly with pre-amp tubes.
my previous exp. is mostly with pre-amp tubes.
0 x
-
- Frequent poster
- Posts: 922
- Joined: Wed 09/29/04 2:00 am
- Location: East Yorkshire
There's not much choice in new valves today, anyway - there are Chinese factories making stuff that doesn't interest most guitarists, the ElectroHarmonix factory in St Petersberg makes most of the modern production varieties, and JJ is the only other factory making new valves. Apart from those, the Ei factory has been threatening to restart production for a long time, but it hasn't happened yet.
In an 18watt, you generally find that NOS valves sound smooth in comparison to the ElectroHarmonix products, but JJs also sound smooth. I would expect the JJs to sound a little brighter than those russkis you bought, but the JJs probably won't last as long - the Russkis were routinely tested for a 3,000 hour service life. Lots of people find JJs have a pleasant sound and good reputation (although I have heard people complaining about the JJ version of the EZ81).
It really does depend on the amp design, whether you can tell the difference in a modern amp. A (pro) friend of mine bought a far-east built Bogen a while back, and it says in the manual that using NOS valves will only improve the sound. We tried a lot of NOS valves in it. We tried old Mullard, Brimar, Ei, Raytheon and Sylvania 12AX7 and Mullard EL84 - all pre 65 (except the Raytheons). We could not see any significant difference over the Chinese valves it came with ...
In an 18watt, you generally find that NOS valves sound smooth in comparison to the ElectroHarmonix products, but JJs also sound smooth. I would expect the JJs to sound a little brighter than those russkis you bought, but the JJs probably won't last as long - the Russkis were routinely tested for a 3,000 hour service life. Lots of people find JJs have a pleasant sound and good reputation (although I have heard people complaining about the JJ version of the EZ81).
It really does depend on the amp design, whether you can tell the difference in a modern amp. A (pro) friend of mine bought a far-east built Bogen a while back, and it says in the manual that using NOS valves will only improve the sound. We tried a lot of NOS valves in it. We tried old Mullard, Brimar, Ei, Raytheon and Sylvania 12AX7 and Mullard EL84 - all pre 65 (except the Raytheons). We could not see any significant difference over the Chinese valves it came with ...
0 x
-
- Senior Amp Tech
- Posts: 1169
- Joined: Sat 08/09/08 2:00 am
- Location: Columbia River Gorge, Oregon Side
-
- Newbie
- Posts: 77
- Joined: Sun 04/25/10 2:00 am
- Location: Canada
- zaphod_phil
- Builder, Admin
- Posts: 15208
- Joined: Wed 03/19/03 2:00 am
- Location: YYZ
All the different Marshall 18W amp variants sound great with 6V6s. Take your pick. Just change three resistor values to accommodate the 6V6s and away you go. Be prepared for quite a bit more bass.
This is still an 18W amp discussion. You are allowed to change the amp's power tubes, and there's nothing new about running 6V6s in a Marshall 18W. Same with EL34s or 6L6s for that matter.Well I was pulled up a little while back for bringing non-18W amp discussion here, so I was playing it safe but you raise a very valid point
0 x
Nature abhors a clean tube amp
-
- Frequent poster
- Posts: 922
- Joined: Wed 09/29/04 2:00 am
- Location: East Yorkshire
O Yez - got to admit that my 18 has Elpico written on it!
I just read what I wrote - and the picture is not complete, ElectroHarmonix are getting valves made in Saratov, too, although I'm not sure if they have bought the factory. And there are still valves coming out of Voskhod, but nothing to interest the 18W community.
I just read what I wrote - and the picture is not complete, ElectroHarmonix are getting valves made in Saratov, too, although I'm not sure if they have bought the factory. And there are still valves coming out of Voskhod, but nothing to interest the 18W community.
0 x
- apexjr
- Occasional poster
- Posts: 110
- Joined: Tue 02/17/04 2:00 am
- Location: California
- Contact:
-
- Frequent poster
- Posts: 922
- Joined: Wed 09/29/04 2:00 am
- Location: East Yorkshire
Antimony still has some uses in semiconductors, and does not present a hazard when enclosed in a glass envelope. Mercury is in just about every low energy light bulb you see ...
The real hazardous material in old valves is Thorium. I have never got to the bottom of how it was used, but it appears to be part of the "black magic" cathode coating.
The real hazardous material in old valves is Thorium. I have never got to the bottom of how it was used, but it appears to be part of the "black magic" cathode coating.
0 x
- zaphod_phil
- Builder, Admin
- Posts: 15208
- Joined: Wed 03/19/03 2:00 am
- Location: YYZ
Thoriated tungsten was used for the filaments in directly-heated high power valves, such as would be used in radio transmitters. I haven't seen any evidence of thorium being used in cathodes of lower power radio and audio valves. I do still wonder if it might perhaps have been used in directly-heated rectifiers, such as 5Y3s or 5U4s.....
0 x
Nature abhors a clean tube amp
-
- Senior Amp Tech
- Posts: 1169
- Joined: Sat 08/09/08 2:00 am
- Location: Columbia River Gorge, Oregon Side
-
- Frequent poster
- Posts: 922
- Joined: Wed 09/29/04 2:00 am
- Location: East Yorkshire
We've had this discussion before, Phil - you talk to too many people!
It's in the COATING, not the alloy. Beyond that, I have never found out much info. Even when you get a detailed description of the coating process, it comes under the category of "traces of other chemicals" when the coating composition is described.
It's in the COATING, not the alloy. Beyond that, I have never found out much info. Even when you get a detailed description of the coating process, it comes under the category of "traces of other chemicals" when the coating composition is described.
0 x
-
- Unrated
- Posts: 3
- Joined: Wed 05/24/06 2:00 am
- Location: bremen
hi folks,
i bought on ebay an old mullard ecc 83, and this makes an explicit difference in sound compared to new tungsol (pretty good too), J.J or TAD.
for outputstage i like the new j.j el 84, nos brimar seem to be damaged, so i don´t know.
from a oldstyle radio repairshop i got some old telefunken and valvo.
i`m curious, how they will sound in my ceriatone 18 w.
i bought on ebay an old mullard ecc 83, and this makes an explicit difference in sound compared to new tungsol (pretty good too), J.J or TAD.
for outputstage i like the new j.j el 84, nos brimar seem to be damaged, so i don´t know.
from a oldstyle radio repairshop i got some old telefunken and valvo.
i`m curious, how they will sound in my ceriatone 18 w.
0 x
- zaphod_phil
- Builder, Admin
- Posts: 15208
- Joined: Wed 03/19/03 2:00 am
- Location: YYZ
Old Mullard ECC83s are my favourite preamp valves. The new (fake) Russian-made Mullard ECC83/12AX7s also have a very sweet tone, but don't sound much like the the real ones. Valvo and Mullard are also very similar, as they were both part of the Philips group. Sometimes you find Valvo valves with production codes showing they were actually made by Mullard in England. I've never tried Telefunken ECC83s, but I've heard that they sound amazing.
In modern production, the fake Russian-made Mullard EL84s also sound really good. JJs are good too, although to me they lack some character. You should try to see if you can get some Saratovs. Or else convert the socket connections for EL83s, and use NOS EL83s, which are much easier to buy at reasonable prices. Oops, I maybe shouldn't have said that!
In modern production, the fake Russian-made Mullard EL84s also sound really good. JJs are good too, although to me they lack some character. You should try to see if you can get some Saratovs. Or else convert the socket connections for EL83s, and use NOS EL83s, which are much easier to buy at reasonable prices. Oops, I maybe shouldn't have said that!
0 x
Nature abhors a clean tube amp
-
- Unrated
- Posts: 3
- Joined: Wed 05/24/06 2:00 am
- Location: bremen
muchas gracias for this tips, i will check out some.
telefunken ecc83 sound a little bit more "analytic" than mullard, a bit more "silk" but "velvet".
hifi freaks are looking for them, and a nos pair cost easily 150 $ and more on ebay.
i got some used about 50 years old telefunken (and valvo, rft, siemens & halske, a.s.o.) from a guy, who renovates radios from 50ies.
maybe those tubes still don`t work on 100%, for me it sounds pretty cool in different amps (div. silverface fender, ceria 18 w, callaham el 34).
telefunken ecc83 sound a little bit more "analytic" than mullard, a bit more "silk" but "velvet".
hifi freaks are looking for them, and a nos pair cost easily 150 $ and more on ebay.
i got some used about 50 years old telefunken (and valvo, rft, siemens & halske, a.s.o.) from a guy, who renovates radios from 50ies.
maybe those tubes still don`t work on 100%, for me it sounds pretty cool in different amps (div. silverface fender, ceria 18 w, callaham el 34).
0 x
-
- Occasional poster
- Posts: 254
- Joined: Thu 06/11/09 2:00 am
- Location: queensland, Australia
i too got some Saratov EL-84'S from him aswell, and found them good, although when using my vvr (pa and pi)(low volumes) jjs sounded better
my nos's seem to go fizzy when turning vvr to 50% or below?
but the jjs would only go fizzy (hard to describe) at <30%,
although when cranking the amp Saratov EL-84'S sound to my ear an improvement to jjs
my nos's seem to go fizzy when turning vvr to 50% or below?
but the jjs would only go fizzy (hard to describe) at <30%,
although when cranking the amp Saratov EL-84'S sound to my ear an improvement to jjs
0 x